Marvel, Doall, Hyd-Mech, and HEM Saw Aftermarket Band Saw Parts

Categories

    Oil Seal Input Shaft

    $29.46
    This is an input seal or radial lip seal on the transmission which fits the input shaft behind the flywheel.

    Filter Element 81-Cbr49

    $129.87
    This is a cartridge style filter element which fits in the P AB 25-CB49 filter housing.

    Bronze Bushing 81-Ba154

    $4.83
    This Bushing is used on chip brush units powered by the transmission flywheel. Each unit takes one P AB 25-BA109 Bronze Bushings. Also known as Bronze Bushing 81-BA154*

    Shut Off Coupling (Female)

    $73.03
    Shut Off Coupling or Quick Disconnect (female side) for vise Hydraulic line.

    Drive Shaft

    $1,162.04
    This output shaft is for newer model 25 transmissions with tapered roller bearings.

    Coolant Pump

    $3,142.80
    A centrifugal pump which supplies coolant to the saw blade. Also recommended is the P AB 25-DBR6-C intake screen.

    Insert Assembly

    $1,970.58
    These DOALL Guides are on DOALL TF Series Machines using a 1.25 Sawblade. This Guide Mounts solid to adjustable guide arm. A complete set will require one of each: 112089, 112090, 119350 or 119354. This guide Floats on lower guide post.

    Insert Asm Tf25 1 1/2 Lh Upper

    $1,970.58
    This is a Upper Left 1 1/2 Band Saw Blade Guide, this guide will fit the following DoAll Machines: TF-24, TF-25 The complete set of 4 will include the following part numbers: 141942, 141943, 141944 and 141945 This Guide Mounts solid on Guide Arm.

    DoAll 1.50 Inch Horz Guide Set

    $602.00
    Fits Model C1220 & Older 1.500 Saws using the following part numbers: 147670 Left Fixed 159309 Left Adjustable 147610 Right Fixed 159310 Right Adustable

    Right Front Insert 1 1/2

    $1,970.58
    Right Front Insert 1 1/2 * This is a Right Back Blade Guide this blade guide will fit the following DoAll Machines: C-1220 and other DoAll 1.5 Horizontal sawing machines This guide mounts solid on Guide Arm.

    Insert Assembly

    $1,970.58
    These DOALL Guides are on DOALL TF Series Machines using a 1.25 Sawblade. This Guide Mounts solid to adjustable guide arm. A complete set will require one of each: 112089, 112090, 119350 or 119354. This Guide mounts solid on lower guide post.

    Insert Asm Tf25 1 1/2 Rh Lower

    $775.97
    This is a Lower Right 1 1/2 Band Saw Blade Guide, this guide will fit the following DoAll Machines: TF-24, TF-25 The complete set of 4 will include the following part numbers: 141942, 141943, 141944, and 141945. This outside insert floats and is adjusted to Rear Guide for proper clearance.

    Cut Watcher Carbide

    $114.07
    Cut Watcher Carbide Insert

    Fixed Plate Adapter

    $668.91
    P HEM D-10582-5-1 This is the Inner Guide Mount Assembly for the Fixed Guide Arm.

    Link For Enhancer – Thick

    $71.17
    P HEM A-11949-16-1-A. Enhancer link connects Back-Up Guide to enhancer cylinder assembly. Holding Back-Up carbide in place allowing assembly to pivot (4 are needed per machine)

    Seal Kit for Pwd. Guide Arm Cy

    $44.81

    Side Guide 2 5/8

    $317.00
    2 5/8 side guide

    Guide Clamps

    $118.16
    Complete Guide Clamp Handle and Bellville Washers includes: Bellville Washers= 340260, Handle = S20-328-02, Lock Pin / Set Screw = S20-328-01

    Side Guide 3

    $375.00
    3 side guide

    Hyd-Mech S-25 Guide Set 1 1/2

    $450.80
    Hydmech Bandsaw Blade Guides - 1.50. Guides are sold as a set of four per machine. These Guides support the Sawblade during cutting holding the blade Perpendicular to Saw Base. This will fit all S-25 machines that run the 1 1/2 blades